Publicaciones

• Article dans une revue

Investigation of the performance of modified TCM scheme for the protection of SPIHT-based compressed images over fading channel

Mohamed Ben Aissa, Abdesselam Bassou, Mohammed Beladgham, Abdelmalik Taleb-Ahmed, Abdelmounaim Moulay Lakhdar

In this paper, a new variant of trellis-coded modulation with Ungerboeck-Gray mapping 'TCM-UGM' is presented for spectral efficiency of 2 bit/s/Hz. The performance of this encoding scheme is investigated over Rayleigh fading channel. The simulation result, using 16-state TCM-UGM encoder,...

International Review on Computers and Software (IRECOS), 2013, 8 (1), pp.271-276. ⟨hal-03507984⟩

• Chapitre d'ouvrage

Estimation of Road Adhesion Coefficient Using Higher-Order Sliding Mode Observer for Torsional Tyre Model

Jagat Jyoti Rath, Kalyana Chakravarthy Veluvolu, D. Zhang, Q. Zhang, Michael Defoort

The estimation of friction coefficient for a vehicle when it traverses on different surfaces has been an important issue. In this paper, a super-twisting algorithm based sliding mode observer is proposed to estimate the road adhesion coefficient, treated as an unknown input in the dynamics of a...

Intelligent Robotics and Applications, 8103, Springer Berlin Heidelberg, pp.202-213, 2013, Lecture Notes in Computer Science, ⟨10.1007/978-3-642-40849-6_18⟩. ⟨hal-03621911⟩

• Communication dans un congrès

Des Honeypots Mobiles Pour La Sécurité Proactive des Réseaux Ad Hoc Véhiculaires (VANETs)

Dhavy Gantsou, Patrick Sondi Obwang

Colloque international TELECOM’2013 & 8ème JFMMA, 2013, Marrakech, Maroc. ⟨hal-03577439⟩

• Article dans une revue

A three-dimensional study of electronic component cooling using a flat heat pipe

Hamdy Hassan, Souad Harmand

In this article, a three-dimensional thermal and hydrodynamic numerical model using a flat heat pipe (vapor chamber) is proposed for cooling of electronic components. The heat pipe is composed of a vapor region sandwiched between two wick regions, which are covered by two flat copper plates. A...

Heat Transfer Engineering, 2013, 34 (7), pp.596-607. ⟨10.1080/01457632.2013.730426⟩. ⟨hal-03531174⟩

• Communication dans un congrès

Alternative Action Plan Generator (A2PG) for elaboration an anticipated feedback

Wided Ben Yahia, Nicolas Tricot, Philippe Polet, Frédéric Vanderhaegen

This paper proposes an original Alternative Action Plan Generator – A2PG, which predicts possible alternatives of the human action plans in which the human operators do not respect the safety rules. These alternatives build an anticipated feedback. Five parameters characterize A2PG. The creation of...

12th IFAC Symposium on Analysis, Design, and Evaluation of Human-Machine Systems, Aug 2013, Las Vegas, Nevada, United States. pp.296-303, ⟨10.3182/20130811-5-US-2037.00069⟩. ⟨hal-03612502⟩

• Article dans une revue

Unified Driver Model simulation and its application to the automotive, rail and maritime domains

Pietro Carlo Cacciabue, Simon Enjalbert, Håkan Söderberg, Andreas Tapani

This paper describes the implementation of a model of a driver into a computerised numerical simulation. The model is developed to capture the essential characteristics and common aspects of cognition and behaviour of a human being in control of a “vehicle” in different surface transport systems,...

Transportation Research Part F: Traffic Psychology and Behaviour, 2013, 21, pp.315-327. ⟨10.1016/j.trf.2013.09.020⟩. ⟨hal-03509701⟩

• Article dans une revue

Energetic optimization of the performances of a hot air engine for micro-CHP systems working with a Joule or an Ericsson cycle

Marie Creyx, Eric Delacourt, Céline Morin, Bernard Desmet, Philippe Peultier

The micro combined heat and electrical power systems (micro-CHP) with hot air engines are well adapted for solid biomass upgrading, in particular, the Ericsson engines working with an open cycle and an external combustion. This paper presents a model of an Ericsson engine with a compression and an...

Energy, 2013, 49 (1), pp. 229-239. ⟨10.1016/j.energy.2012.10.061⟩. ⟨hal-03531364⟩

• Article dans une revue

A comprehensive blank development method for forming sheet metal parts

Jianjun Wu, Xin Wu, Liangcai Deng, Hakim Naceur

For some shortcomings in the use of standard radial length development in the blank development for forming sheet metal parts, an improved radial length normal spreading approach considering outside normal direction is developed to resolve blank development in sheet metal forming. Moreover, a...

International Journal of Advanced Manufacturing Technology, 2013, 13 (1), pp. 1-13. ⟨10.1007/s00170-013-5502-z⟩. ⟨hal-03520429⟩

• Article dans une revue

Assessment of ship maneuverability by using a coupling between a nonlinear transient ship maneuvering model and mathematical programming techniques

T. Tran Khanh, Abdellatif Ouahsine, Hakim Naceur, Karima El Wassifi

In this paper, a numerical method based on a coupling between a mathematical model of nonlinear transient ship manoeuvring motion in the horizontal plane and Mathematical Programming (MP) techniques is proposed. The aim of the proposed procedure is an efficient estimation of optimal ship...

Journal of Hydrodynamics, 2013, 25 (5), pp.788-804. ⟨10.1016/S1001-6058(13)60426-6⟩. ⟨hal-03629803⟩

• Communication dans un congrès

Structural Self-organized Holonic Multi-Agent Manufacturing Systems

José Barbosa, Paulo Leitão, Emmanuel Adam, Damien Trentesaux

Worldwide systems are increasingly growing into unprecedented complexity levels. This increase of system complexity has to be tackled with new control approaches, where decentralization is playing an important role and particularly the Multi-Agent Systems and Holonic Systems. Despite the benefits...

6th International Conference on Industrial Applications of Holonic and Multi-Agent Systems (HoloMAS 2013), Aug 2013, Prague, Czech Republic. pp.59-70, ⟨10.1007/978-3-642-40090-2_6⟩. ⟨hal-03467679⟩