Publicaciones

• Communication dans un congrès

Interactive tabletops as new supports for collective diagnosis ?

Christophe Kolski, Yoann Lebrun, Bako Rajaonah, Sophie Lepreux, René Mandiau

The central question described in this paper concerns the possible use of interactive tabletops as new supports for collective diagnosis. A model called Collective Diagnosis Architecture (CDA) is proposed. An innovative application developed on two interactive tabletops equipped with RFID...

Foundations and Applications of Human-Machine Interaction, 10th Workshop on Human-Machine Systems, Oct 2013, Berlin, Germany. pp.167-172. ⟨hal-03384077⟩

• Communication dans un congrès

Intelligent Products: A Spinal Column to Handle Information Exchanges in Supply Chains

Damien Trentesaux, Bernard Grabot, Yves Sallez

This paper outlines some practical problems linked to information exchange occurring in nowadays supply chains, with a special emphasis on the aeronautical sector. The Intelligent Product paradigm is presented as an adequate solution to address some of these problems and to provide rapid gains...

20th Advances in Production Management Systems (APMS), Sep 2013, State College, PA, United States. pp.452-459, ⟨10.1007/978-3-642-41263-9_56⟩. ⟨hal-01449753⟩

• Article dans une revue

Influence of the roughness of sandblasted surface on the measurement of hardness by nanoindentation, Influence de l’amplitude de la rugosité de surfaces sablées sur la mesure de dureté par nanoindentation

Hsin Shen Ho, Yang Xia, Julie Marteau, Maxence Bigerelle

Nanoindentation tests are often used to characterize the surface mechanical properties of materials. However, this technique lacks repeatability: when different zones of the same specimen are tested, there can be large differences between the nanoindentation curves. One of the main causes is the..., Les essais de nanoindentation sont souvent utilisés pour caractériser les propriétés mécaniques des matériaux en proche surface. Cependant, cette technique manque de reproductibilité : une même réponse mécanique est difficilement obtenue par les essais de nanoindentation sur différentes zones de la...

Matériaux et Techniques, 2013, 101 (3), pp.305. ⟨10.1051/mattech/2013070⟩. ⟨hal-02968730⟩

• Communication dans un congrès

Ankle joint moment is substantially underestimated when measured with classical ergometers mounted with a uni-dimensional force sensor

Emilie Simoneau-Buessinger, Anis Toumi, Christophe Gillet, Sebastien Leteneur

XVIIIth Annual Congress of the European College of Sport Sciences (ECSS), Jan 2013, Barcelone, Spain. ⟨hal-03533968⟩

• Communication dans un congrès

Validation of a new numerical weaving tool highlighting the influence of real yarn positions and shapes on their behaviour under impact

Mickael Lequin, E. Ferry, Benjamin Provost, Daniel Coutellier, François Boussu

In this study, a numerical simulation approach is used to measure the influence of yarn positions inside a 3D warp interlock fabric submitted to impact. Four numerical results have been compared to one experimental impact test. A first simulation is made directly from the experimental tomographic...

13th AUTEX World Textile Conference, May 2013, Dresde, Germany. ⟨hal-03512879⟩

• Article dans une revue

Analysis of inverse method applied on sandwich probes

Emna Berrich, Fethi Aloui, Jack Legrand

Parallel plate disks (PPD) are often used for analyzing the effect of small amplitude oscillations with different frequencies. These devices allow the imposing of a well-known flow kinematics. Mass transfer problems and, particularly, convection-diffusion problems relating wall shear rate to mass...

Journal of Fluids Engineering, 2013, 135 (1), ⟨10.1115/1.4007888⟩. ⟨hal-03521107⟩

• Communication dans un congrès

Optimal Design of a High Performance Haptic Device

Quoc Viet Dang, Antoine Dequidt, Laurent Vermeiren, Michel Dambrine

Stability and transparency are very important performance measures in the design of haptic devices. This paper addresses the design of haptic device in the case of interaction to a virtual wall. A novel optimal design method for high performance (stability and low inertia) haptic devices is...

EEE International Conference on Mechatronics, Feb 2013, Vicence, Italy. ⟨hal-03467293⟩

• Ouvrages

Trends in Practical Applications of Agents and Multiagent Systems

Philippe Mathieu, Emmanuel Adam

Springer, pp.210, 2013. ⟨hal-00826623⟩

• Chapitre d'ouvrage

FEM Simulation Based on CAD Model Simplification: A Comparison Study between the Hybrid Method and the Technique Using a Removing Details

Mounir Hamdi, Nizar Aifaoui, Borhen Louhichi, Abdelmajid Benamara, Dominique Deneux

The simulation process is currently used in the design and dimensioning of mechanical parts. With the progress of computer materials, the Finite Elements Method (FEM) becomes the most used approach in the simulation of mechanical behavior. The simulation process needs multiple Design-FEM loops. In...

Design and Modeling of Mechanical Systems, Springer Berlin Heidelberg, pp.587-596, 2013, Lecture Notes in Mechanical Engineering, ⟨10.1007/978-3-642-37143-1_70⟩. ⟨hal-03621588⟩

• Article dans une revue

A simple real-time aerodynamic model for vehicles in overtaking situations

Fredrik Bruzelius, David Uystepruyst, Bengt Jacobson, Siniša Krajnovic

Aerodynamic forces and moments play an important role in overtaking situations and affect the trajectory of the involved vehicles. One method of studying these effects and how the driver responds to these is via driving simulator studies. However, models that describe aerodynamic forces and moments...

International Journal of Vehicle Systems Modelling and Testing, 2013, 8 (3), pp.241-259. ⟨10.1504/IJVSMT.2013.056037⟩. ⟨hal-03470682⟩