Publicaciones

• Communication dans un congrès

Attente en bord de rue de piétons adultes avant une traversée : positionnement et ressenti en fonction de l'âge

Delphine Caffier, Sylvain Cremoux, Franck Barbier, Aurélie Dageons, Janick Naveteur

COPIE 2016, 2016, Paris, France. ⟨hal-03457078⟩

• Article dans une revue

Hybrid DCT-DBT algorithm for medical video compression

Yassine Habchi, Mohammed Beladgham, Haouari Benlabbes, Abdelmalik Taleb-Ahmed

In this paper we present the effect of transform type in medical video compression. To obtain the maximal capabilities of storage and transmission, different compression algorithms should be compared to find the optimal technique for medical video compression. We use for compression three type of...

Electrotehnică, Electronică, Automatică, 2016, 64 (2), pp.97-103. ⟨hal-03669146⟩

• Article dans une revue

Behaviour of flow dynamics over an asymmetrical deep cavity at high reynolds numbers

Denis Cornu, Laurent Keirsbulck, Camila Chovet, Marc Lippert, Franck Kerhervé, Fethi Aloui

This paper presents an experimental study, based on the geometry of a cavity, about the flow effects using quantitative particle image velocimetry (PIV) and, local and instantaneous pressure measurements. Three configurations of rectangular deep cavities were investigated: symmetric and asymmetric...

Civil-Comp Proceedings, 2016, 110, ⟨10.4203/ccp.110.59⟩. ⟨hal-03668719⟩

• Article dans une revue

Relationship between brightness and roughness of polypropylene abraded surfaces

Adrien van Gorp, Maxence Bigerelle, Denis Najjar

This article proposes to analyze the relation between gloss and roughness of surfaces of polypropylene samples abraded at different magnitudes. Experiments consist of mechanical polishing at different grades, roughness profiles measurement, and specular light reflectometry with three incidence...

Polymer Engineering and Science, 2016, 56 (1), pp.103 - 117. ⟨10.1002/pen.24197⟩. ⟨hal-01714922⟩

• Communication dans un congrès

Advanced model based air path management using a discrete-angular controller in idle-speed context

Thomas Laurain, Jimmy Lauber, Reinaldo Martinez Palhares

This paper aims to present an original methodology to design a controller for the air path management considered as a nonlinear system that is presented as a periodic discrete Takagi-Sugeno (TS) model. A transformation is realized to translate the periodic behavior into a classic discrete model...

IFAC AAC, Jun 2016, Norkköping, Sweden. pp.611-618, ⟨10.1016/j.ifacol.2016.08.089⟩. ⟨hal-03407068⟩

• Article dans une revue

Spatial Resolution Correction for Electrochemical Wall-shear Stress Measurements using Rectangular Sensors

Fawzi Fadla, Rogelio Chovet, Denis Cornu, Marc Lippert, Fethi Aloui, Laurent Keirsbulck

This article is mainly motivated by the growing needs for highly resolved measurements forwall-bounded turbulent flows and aims to proposes a spatial correction coefficient in order toincrease the wall-shear stress sensors accuracy. As it well known for the hot wire anemometry, thefluctuating...

Journal of Applied Fluid Mechanics, 2016, 9 (3), pp.1309-1319. ⟨10.18869/acadpub.jafm.68.228.23945⟩. ⟨hal-03448317⟩

• Communication dans un congrès

Classification et analyse des pistes de recherche relatives au CONWIP

Yann Jaegler, Patrick Burlat, Samir Lamouri, Damien Trentesaux

Les grands enjeux industriels actuels se traduisent par une demande de personnalisation des produits, de délais de livraison réduits, de taux de service en hausse et de systèmes productifs agiles. Ils élèvent le choix du système de contrôle de production au rang de sujet stratégique pour une usine...

Classification et analyse des pistes de recherche relatives au CONWIP . 11e Conférence Francophone d’Optimisation et Simulation- MOSIM’16 : « L’innovation technologique au service des systèmes : défis et opportunités», Aug 2016, Montréal, Canada. ⟨emse-01533191⟩

• Article dans une revue

Some improvements for determining the hardness of homogeneous materials from the work-of-indentation

Didier Chicot, Michel Yetna N'Jock, Francine Roudet, Xavier Decoopman, Mariana H. Staia, Eli Saúl Puchi-Cabrera

In this work, the total and plastic hardness of a variety of materials were determined from the work-of-indentation. We show that by taking into account the influence of the tip defect, both the total and plastic hardness have the same values and that the hardness-load dependence is considerably...

International Journal of Mechanical Sciences, 2016, 105, pp.279-290. ⟨10.1016/j.ijmecsci.2015.11.030⟩. ⟨hal-01249912⟩

• Communication dans un congrès

An Iterative Greedy Insertion Technique for Flexible Job Shop Scheduling Problem

Azzedine Bekkar, Oualid Guemri, Abdelghani Bekrar, Nassima Aissani, Bouziane Beldjilali, Damien Trentesaux

This paper studies the problem of scheduling in a flexible job shop. A greedy heuristic is developed to solve precisely the sequencing (allocation) problem. The principle of this approach is to iteratively insert operations on the machines until the objective of minimizing the Cmax (makespan) is...

8th IFAC Conference on Manufacturing Modelling, Management and Control MIM 2016, Dec 2016, Troyes, France. pp.1956-1961, ⟨10.1016/j.ifacol.2016.07.917⟩. ⟨hal-03406967⟩

• Article dans une revue

Modelling Laminate Failure in Composite Materials for Automotive Applications

David Moncayo, F. Köster, Pedro P Camanho, Daniel Coutellier, S. Hartmann

In order to capture the complexity of material failure it is necessary to understand that the performance of FE models depends on a fair use and a fair modeling of composite materials. Based on previous research works, the prognosis capabilities of the current material definitions in LS-DYNA will...

FEA Information Engineering Journal, 2016, 5 (6), pp.1-24. ⟨hal-03445539⟩