Publicaciones

• Communication dans un congrès

Interactive tabletops as new supports for collective diagnosis ?

Christophe Kolski, Yoann Lebrun, Bako Rajaonah, Sophie Lepreux, René Mandiau

The central question described in this paper concerns the possible use of interactive tabletops as new supports for collective diagnosis. A model called Collective Diagnosis Architecture (CDA) is proposed. An innovative application developed on two interactive tabletops equipped with RFID...

Foundations and Applications of Human-Machine Interaction, 10th Workshop on Human-Machine Systems, Oct 2013, Berlin, Germany. pp.167-172. ⟨hal-03384077⟩

• Communication dans un congrès

Intelligent Products: A Spinal Column to Handle Information Exchanges in Supply Chains

Damien Trentesaux, Bernard Grabot, Yves Sallez

This paper outlines some practical problems linked to information exchange occurring in nowadays supply chains, with a special emphasis on the aeronautical sector. The Intelligent Product paradigm is presented as an adequate solution to address some of these problems and to provide rapid gains...

20th Advances in Production Management Systems (APMS), Sep 2013, State College, PA, United States. pp.452-459, ⟨10.1007/978-3-642-41263-9_56⟩. ⟨hal-01449753⟩

• Article dans une revue

Influence of the roughness of sandblasted surface on the measurement of hardness by nanoindentation, Influence de l’amplitude de la rugosité de surfaces sablées sur la mesure de dureté par nanoindentation

Hsin Shen Ho, Yang Xia, Julie Marteau, Maxence Bigerelle

Nanoindentation tests are often used to characterize the surface mechanical properties of materials. However, this technique lacks repeatability: when different zones of the same specimen are tested, there can be large differences between the nanoindentation curves. One of the main causes is the..., Les essais de nanoindentation sont souvent utilisés pour caractériser les propriétés mécaniques des matériaux en proche surface. Cependant, cette technique manque de reproductibilité : une même réponse mécanique est difficilement obtenue par les essais de nanoindentation sur différentes zones de la...

Matériaux et Techniques, 2013, 101 (3), pp.305. ⟨10.1051/mattech/2013070⟩. ⟨hal-02968730⟩

• Communication dans un congrès

Ankle joint moment is substantially underestimated when measured with classical ergometers mounted with a uni-dimensional force sensor

Emilie Simoneau-Buessinger, Anis Toumi, Christophe Gillet, Sebastien Leteneur

XVIIIth Annual Congress of the European College of Sport Sciences (ECSS), Jan 2013, Barcelone, Spain. ⟨hal-03533968⟩

• Communication dans un congrès

Validation of a new numerical weaving tool highlighting the influence of real yarn positions and shapes on their behaviour under impact

Mickael Lequin, E. Ferry, Benjamin Provost, Daniel Coutellier, François Boussu

In this study, a numerical simulation approach is used to measure the influence of yarn positions inside a 3D warp interlock fabric submitted to impact. Four numerical results have been compared to one experimental impact test. A first simulation is made directly from the experimental tomographic...

13th AUTEX World Textile Conference, May 2013, Dresde, Germany. ⟨hal-03512879⟩

• Article dans une revue

Analysis of inverse method applied on sandwich probes

Emna Berrich, Fethi Aloui, Jack Legrand

Parallel plate disks (PPD) are often used for analyzing the effect of small amplitude oscillations with different frequencies. These devices allow the imposing of a well-known flow kinematics. Mass transfer problems and, particularly, convection-diffusion problems relating wall shear rate to mass...

Journal of Fluids Engineering, 2013, 135 (1), ⟨10.1115/1.4007888⟩. ⟨hal-03521107⟩

• Article dans une revue

Roughness signature of tribological contact calculated by a new method of peaks curvature radius estimation on fractal surfaces

Maxence Bigerelle, Jean-Marie Nianga, Denis Najjar, Alain Iost, Cédric Hubert, K. J. Kubiak

This paper proposes a new method of roughness peaks curvature radii calculation and its application to tribological contact analysis as characteristic signature of tribological contact. This method is introduced via the classical approach of the calculation of radius of asperity. In fact, the...

Tribology International, 2013, 65 (65), pp.235-247. ⟨10.1016/j.triboint.2013.03.017⟩. ⟨hal-01065878⟩

• Communication dans un congrès

Alternative Action Plan Generator (A2PG) for elaboration an anticipated feedback

Wided Ben Yahia, Nicolas Tricot, Philippe Polet, Frédéric Vanderhaegen

This paper proposes an original Alternative Action Plan Generator – A2PG, which predicts possible alternatives of the human action plans in which the human operators do not respect the safety rules. These alternatives build an anticipated feedback. Five parameters characterize A2PG. The creation of...

12th IFAC Symposium on Analysis, Design, and Evaluation of Human-Machine Systems, Aug 2013, Las Vegas, Nevada, United States. pp.296-303, ⟨10.3182/20130811-5-US-2037.00069⟩. ⟨hal-03612502⟩

• Article dans une revue

A comprehensive blank development method for forming sheet metal parts

Jianjun Wu, Xin Wu, Liangcai Deng, Hakim Naceur

For some shortcomings in the use of standard radial length development in the blank development for forming sheet metal parts, an improved radial length normal spreading approach considering outside normal direction is developed to resolve blank development in sheet metal forming. Moreover, a...

International Journal of Advanced Manufacturing Technology, 2013, 13 (1), pp. 1-13. ⟨10.1007/s00170-013-5502-z⟩. ⟨hal-03520429⟩

• Ouvrages

Social, Localisation et Mobilité : de nouveaux enjeux pour la gestion des données

Florence Sèdes, Thierry Delot

Sèdes, Florence; Delot, Thierry. Hermès Science, Numéro spécial (18 : 1), 2013, Ingénierie des Systèmes d'Information (ISI), ISSN 1633-1311. ⟨hal-03761353⟩