Publications

• Article dans une revue

Study of the parameters and characteristics of flat heat pipe with nanofluids subjected to periodic heat load on its performance

Hamdy Hassan, Souad Harmand

A study is presented on the transient cooling of an electronic component by flat heat pipe (FHP) with nanofluid. The electronic component has periodic power output of maximum value 400 W and works for 12.8 s. The effects of Cu, CuO and Al2O3 nanoparticles on the heat pipe performance are…

International Journal of Thermal Sciences, 2015, 97, pp.126-142. ⟨10.1016/j.ijthermalsci.2015.06.009⟩. ⟨hal-03448546⟩

• Article dans une revue

Hardware resource utilization optimization in FPGA-based Heterogeneous MPSoC architectures

Bouthaina Dammak Masmoudi, Mouna Baklouti, Rachid Benmansour, Smail Niar, Mohamed Abid

Next generation FPGA circuits will allow the integration of dozens of hard and soft cores as well as dedicated accelerators in the same chip. These Heterogeneous Multiprocessor System-on-Chip (Ht-MPSoC) architectures will allow the design of very complex System-on-Chips (SoC) on a single FPGA chip…

Microprocessors and Microsystems: Embedded Hardware Design , 2015, 39 (8), pp.1108-1118. ⟨10.1016/j.micpro.2015.05.006⟩. ⟨hal-03401002⟩

• Article dans une revue

Customizing VLIW processors from dynamically profiled execution traces

Gorker Alp Malazgirt, Arda Yurdakul, Smail Niar

The design philosophy of VLIW processors is to maximize instruction level parallelism (ILP) starting from compiler and machine code level to all the way down to memory and computational blocks. For this purpose, VLIW tailoring has been an important research area, because non-tailored VLIWs cannot…

Microprocessors and Microsystems: Embedded Hardware Design , 2015, 39 (8), pp.656-673. ⟨10.1016/j.micpro.2015.09.005⟩. ⟨hal-03400990⟩

• Article dans une revue

Reactive control of overall power consumption in flexible manufacturing systems scheduling: A Potential Fields model

Cyrille Pach, Thierry Berger, Yves Sallez, Damien Trentesaux

In recent years, designing “energy-aware manufacturing scheduling and control systems” has become more and more complex due to the increasing volatility and unpredictability of energy availability, supply and cost, and thus requires the integration of highly reactive behavior in control laws. The…

Control Engineering Practice, 2015, 44, pp.193-208. ⟨10.1016/j.conengprac.2015.08.003⟩. ⟨hal-03428162⟩

• Article dans une revue

Review on Numerical Modeling of Instrumented Indentation Tests for Elastoplastic Material Behavior Identification

Julie Marteau, Salima Bouvier, Maxence Bigerelle

The impacts of the parameters controlling the finite element simulation of instrumented indentation tests and their consequences on numerical results are reviewed in case of homogeneous materials and functionally graded ones. Through a comparative study of the results of different finite element…

Archives of Computational Methods in Engineering, 2015, 22 (4), pp.577-593. ⟨10.1007/s11831-014-9134-8⟩. ⟨hal-02909095⟩

• Article dans une revue

Enhanced precision of ankle torque measure with an open-unit dynamometer mounted with a 3D force-torque sensor

Anis Toumi, Sebastien Leteneur, Christophe Gillet, Jean-François Debril, Nicolas Decoufour, Franck Barbier, Jennifer Jakobi, Emilie Simoneau-Buessinger

Purpose: Many studies have focused on maximum torque exerted by ankle joint muscles during plantar flexion. While strength parameters are typically measured with isokinetic or isolated ankle dynamometers, these devices often present substantial limitations for the measurement of torque because they…

European Journal of Applied Physiology, 2015, 115 (11), pp.2303-2310. ⟨10.1007/s00421-015-3210-0⟩. ⟨hal-03520701⟩

• Communication dans un congrès

A survey on vision-based traffic accident detection techniques

Boutheina Maaloul, Abdelmalik Taleb-Ahmed, Carlos Valderrama, Smail Niar, Foued Derraz, Naim Harb

International Conference on Advanced Communication Systems and Signal Processing (ICOSIP 2015), Nov 2015, Tlemcen, Algeria. ⟨hal-03384622⟩

• Communication dans un congrès

Routing proposition to face myopia in flexible manufacturing system distributed control

Nassima Aissani, Damien Trentesaux

Decentralized decision-making processes in manufacturing control offer seeking fault-tolerance, scalability, flexibility, adaptability and reactivity. However, many convergence problems appear: decisional entities do not have a clear vision whether or not the system is heading towards its…

CIE 45: 2015 International Conference on Computers and Industrial Engineering, Oct 2015, Metz, France. ⟨hal-03659594⟩

• Communication dans un congrès

Mixed integer programming formulations for the single processor scheduling problem with time restrictions

Rachid Benmansour, Oliver Braun, Abdelhakim Artiba

In the single-processor scheduling problem with time restrictions, n independent jobs have to be processed non-preemptively on a single processor that can handle only one job at a time, subject only to the following constraint: during any time period of length α > 0 the number of jobs being…

CIE 45: 2015 International Conference on Computers and Industrial Engineering, Oct 2015, Metz, France. ⟨hal-03659548⟩

• Communication dans un congrès

An improved multi-agent particle swarm optimization to solve flexible job-shop scheduling problem.

Maroua Nouiri, Abdelghani Bekrar, Abderrazek Jemai, Damien Trentesaux, Ahmed Chiheb Ammari, Smail Niar

Many efficient meta-heuristics methods are developed to solve Flexible Job Scheduling Problem (FJSP) to get nearly optimal solutions that optimize an objective function. However, in real-world manufacturing systems, schedules are often confronted with unexpected factors such as random machine…

45th International Conference on Computers & Industrial Engineering (CIE45), Oct 2015, Metz, France. pp.297-304. ⟨hal-03384957⟩