Publications

Type de document

Mots clés

Auteur

Du

Au

Affichage de 1541 à 1550 sur 2006

Article dans une revue

Lighter tableware ceramic by controlling porosity: Effect of porosity on mechanical properties

Benjamin Verhaeghe, Christian Courtois, F. Petit, F. Cambier, Jean-Dominique Guerin, Anne Leriche, Stuart Hampshire

Reduction in weight of ceramics has been achieved by using a specific porous agent, starch, to achieve porosity ranging from 10% to 35%. Two incorporation routes of the porous agent have been investigated. For different levels of weight reduction, ceramics are characterized by microstructural…

Ceramics International, 2014, 40 (1), pp.763-770. ⟨10.1016/j.ceramint.2013.06.066⟩. ⟨hal-03448297⟩

Article dans une revue

Dynamic evolution of interface roughness during friction and wear processes

K. J. Kubiak, Maxence Bigerelle, T. Mathia, André Dubois, Laurent Dubar

Dynamic evolution of surface roughness and influence of initial roughness (Sa = 0.282–6.73 µm) during friction and wear processes has been analyzed experimentally. The mirror polished and rough surfaces (28 samples in total) have been prepared by surface polishing on Ti–6Al–4V and AISI 1045 samples…

Scanning, 2014, 36 (1), pp.30-38. ⟨10.1002/sca.21082⟩. ⟨hal-03470665⟩

Article dans une revue

Modélisation des performances d’un moteur Ericsson à cycle de joule ouvert

Marie Creyx, Eric Delacourt, Marc Lippert, Céline Morin, Bernard Desmet

The performances of an open Joule cycle Ericsson engine associated to a biomass micro-CHP unit are studied with a dynamic model impl emented with the bond graph formalis m. The dynamic phenomena of the expansion cylinder (pressure drops across the valves, th ermal losses through the cylinder wall,…

Revista Termotehnica, 2014, 1, pp.64-70. ⟨hal-03627090⟩

Article dans une revue

Sliding subspace design based on linear matrix inequalities

Alan Tapia, Raymundo Márquez Borbόn, Miguel Bernal, Joaquín Cortez

In this work, an alternative for sliding surface design based on linear and bilinear matrix inequalities is proposed. The methodology applies for reduced and integral sliding mode control, both continuous- and discrete-time; it takes advantage of the Finsler's lemma to provide a greater degree…

Kybernetika, 2014, 50 (3), pp.436-449. ⟨10.14736/kyb-2014-3-0436⟩. ⟨hal-03663763⟩

Article dans une revue

Ternary Zero Correlation Zone Sequence Sets for Asynchronous DS-CDMA

Benattou Fassi, Ali Djebbari, Abdelmalik Taleb-Ahmed

In this paper we propose a new class of ternary Zero Correlation Zone (ZCZ) sequence sets based on binary ZCZ sequence sets construction. It is shown that the proposed ternary ZCZ sequence sets can reach the upper bound on the ZCZ sequences. The performance of the proposed sequences set in…

Communications and Network, 2014, 06 (04), pp.209-217. ⟨10.4236/cn.2014.64023⟩. ⟨hal-03644466⟩

Article dans une revue

An evidential network approach to support uncertain multiviewpoint abductive reasoning

Felipe Aguirre, Mohamed Sallak, Frédéric Vanderhaegen, Denis Berdjag

The paper proposes an approach to support human abductive reasoning in the diagnosis of a multiviewpoint system. The novelty of this work lies on the capability of the approach to treat the uncertainty held by the agent performing the diagnosis. To do so, we make use of evidential networks to…

Information Sciences, 2013, 250, pp.110-125. ⟨10.1016/j.ins.2013.07.014⟩. ⟨hal-00917053⟩

Article dans une revue

Coupling a genetic algorithm with the distributed arrival-time control for the JIT dynamic scheduling of flexible job-shops

Gabriel Zambrano Rey, Abdelghani Bekrar, Vittaldas V. Prabhu, Damien Trentesaux

In order to increase customer satisfaction and competitiveness, manufacturing systems need to combine flexibility with Just-in-Time (JIT) production. Until now, research on JIT scheduling problems has been mostly limited to high volume assembly lines rather than job-shop-like systems, due to their…

International Journal of Production Research, 2013, 52 (12), pp.3688-3709. ⟨10.1080/00207543.2014.881575⟩. ⟨hal-03649136⟩

Article dans une revue

Fault Detection and Isolation of Aircraft Air Data/Inertial system

Denis Berdjag, Jérome Cieslak, Ali Zolghadri

A method for failure detection and isolation (FDI) for redundant aircraft sensors is presented. The outputs of the concerned sensors are involved in the computation of §ight control laws, and the objective is to eliminate any fault before propagation in the control loop when selecting a unique §…

EUCASS Proceedings Series - Advances in AeroSpace Sciences, 2013, 6, pp.317-332. ⟨10.1051/eucass/201306317⟩. ⟨hal-00913429⟩

Article dans une revue

Reduced numerical model to investigate the dynamic behaviour of honeycombs under mixed shear–compression loading

Rami Tounsi, Bassem Zouari, Fahmi Chaari, Eric Markiewicz, Grégory Haugou, Fakhreddine Dammak

Cellular materials such as aluminium honeycombs combine lightweight with an efficient crash energy absorption capability. They have a major role in a wide range of transport applications to reduce gas emission by the design of lighter structures but remaining safe in accident case. Many…

Thin-Walled Structures, 2013, 73, pp.290-301. ⟨10.1016/j.tws.2013.08.016⟩. ⟨hal-03625158⟩

Article dans une revue

Analysis of thin composite structures using an efficient hex-shell finite element

Seddik Shiri, Hakim Naceur

In this paper a general methodology for the modeling of material composite multilayered shell structures is proposed using a Hex-shell finite element modeling. The first part of the paper is devoted to the general FE formulation of the present composite 8-node Hex-shell element called SCH8, based…

Journal of Mechanical Science and Technology, 2013, 27 (12), pp.3755-3763. ⟨10.1007/s12206-013-0920-2⟩. ⟨hal-03624959⟩