Publications

• Chapitre d'ouvrage

Integer Programming Based Approaches for Multi-Trip Location Routing

Rita Macedo, Cláudio Alves, José Valério De Carvalho, Said Hanafi, Nenad Mladenovic, Bruna Ramos

The multi-trip location routing problem consists in selecting the depots to open and the routes that should be performed to serve a set of clients at minimum cost. The multi-trip variant considers the possibility for a vehicle to perform more than a single route during the planning period, and…

Lecture Notes in Economics and Mathematical Systems, 682, Springer International Publishing, pp.79-90, 2016, ⟨10.1007/978-3-319-20430-7_11⟩. ⟨hal-01592567⟩

• Article dans une revue

Exergy assessment of heat transfer inside a Beta type Stirling engine

Houda Hachem, Ramla Gheith, Fethi Aloui, Sassi Ben Nasrallah, Ibrahim Dincer

This paper presents an assessment of both energy and exergy efficiencies of a Beta Stirling engine prototype with a 30 W capacity as the maximum mechanical power output. Its operating pressure is close to atmospheric pressure, and it supports a maximum hot end temperature of 650 degrees C. The…

International Journal of Exergy, 2016, 20 (2), pp.186-202. ⟨10.1504/IJEX.2016.076863⟩. ⟨hal-03447147⟩

• Article dans une revue

Finding a stabilizing switching law for switching TS models

Zsofia Lendek, Paula Raica, Jimmy Lauber, Thierry-Marie Guerra

This paper considers the stabilisation of switching nonlinear models by switching between the subsystems. We assume that arbitrary switching between two subsystems is possible once a subsystem has been active for a predefined number of samples. We use a Takagi–Sugeno representation of the models…

International Journal of Systems Science, 2016, 47 (12), pp.2762-2772. ⟨10.1080/00207721.2015.1021290⟩. ⟨hal-03430042⟩

• Ouvrages

Special issue: Information Systems in Transport Logistics, International Journal of Shipping and Transport Logistics

Mounir Benaissa, Mourad Abed

Inderscience Publishers, 2016, 1756-6517. ⟨hal-03388662⟩

• Communication dans un congrès

Attente en bord de rue de piétons adultes avant une traversée : positionnement et ressenti en fonction de l'âge

Delphine Caffier, Sylvain Cremoux, Franck Barbier, Aurélie Dageons, Janick Naveteur

COPIE 2016, 2016, Paris, France. ⟨hal-03457078⟩

• Article dans une revue

Some improvements for determining the hardness of homogeneous materials from the work-of-indentation

Didier Chicot, Michel Yetna N'Jock, Francine Roudet, Xavier Decoopman, Mariana H. Staia, Eli Saúl Puchi-Cabrera

In this work, the total and plastic hardness of a variety of materials were determined from the work-of-indentation. We show that by taking into account the influence of the tip defect, both the total and plastic hardness have the same values and that the hardness-load dependence is considerably…

International Journal of Mechanical Sciences, 2016, 105, pp.279-290. ⟨10.1016/j.ijmecsci.2015.11.030⟩. ⟨hal-01249912⟩

• Article dans une revue

Spatial Resolution Correction for Electrochemical Wall-shear Stress Measurements using Rectangular Sensors

Fawzi Fadla, Rogelio Chovet, Denis Cornu, Marc Lippert, Fethi Aloui, Laurent Keirsbulck

This article is mainly motivated by the growing needs for highly resolved measurements forwall-bounded turbulent flows and aims to proposes a spatial correction coefficient in order toincrease the wall-shear stress sensors accuracy. As it well known for the hot wire anemometry, thefluctuating…

Journal of Applied Fluid Mechanics, 2016, 9 (3), pp.1309-1319. ⟨10.18869/acadpub.jafm.68.228.23945⟩. ⟨hal-03448317⟩

• Article dans une revue

Hybrid DCT-DBT algorithm for medical video compression

Yassine Habchi, Mohammed Beladgham, Haouari Benlabbes, Abdelmalik Taleb-Ahmed

In this paper we present the effect of transform type in medical video compression. To obtain the maximal capabilities of storage and transmission, different compression algorithms should be compared to find the optimal technique for medical video compression. We use for compression three type of…

Electrotehnică, Electronică, Automatică, 2016, 64 (2), pp.97-103. ⟨hal-03669146⟩

• Article dans une revue

An approach to the prioritization of sustainable maintenance drivers in the TBL framework

Sandro de Paula Pires, Olivier Sénéchal, Eduardo Rocha Loures, José Fernando Jimenez

The current sustainable production model is supported by the Triple Bottom Line (TBL) concept and its three dimensions: economic, environmental, and social. This paper aims to propose an approach to identify and prioritize the attributes of the TBL dimensions, extracted from the Global Reporting…

IFAC-PapersOnLine, 2016, 49 (28), pp.150-155. ⟨10.1016/j.ifacol.2016.11.026⟩. ⟨hal-03670448⟩

• Communication dans un congrès

An Iterative Greedy Insertion Technique for Flexible Job Shop Scheduling Problem

Azzedine Bekkar, Oualid Guemri, Abdelghani Bekrar, Nassima Aissani, Bouziane Beldjilali, Damien Trentesaux

This paper studies the problem of scheduling in a flexible job shop. A greedy heuristic is developed to solve precisely the sequencing (allocation) problem. The principle of this approach is to iteratively insert operations on the machines until the objective of minimizing the Cmax (makespan) is…

8th IFAC Conference on Manufacturing Modelling, Management and Control MIM 2016, Dec 2016, Troyes, France. pp.1956-1961, ⟨10.1016/j.ifacol.2016.07.917⟩. ⟨hal-03406967⟩